B2B Telecom Equipment Supplier — Request a Quote Todayتأمین‌کننده B2B تجهیزات مخابراتی — امروز درخواست قیمت کنید
B2B Telecom Equipment Supplier — Request a Quote Todayتأمین‌کننده B2B تجهیزات مخابراتی — امروز درخواست قیمت کنید
2G/3G/4G/5G Network Equipment — Nokia, Ericsson, Huawei, ZTE & Moreتجهیزات شبکه 2G/3G/4G/5G — Nokia، Ericsson، Huawei، ZTE و بیشتر
2G/3G/4G/5G Network Equipment — Nokia, Ericsson, Huawei, ZTE & Moreتجهیزات شبکه 2G/3G/4G/5G — Nokia، Ericsson، Huawei، ZTE و بیشتر
Worldwide Shipping
Sea freight, land transport, air freight

SFP vs SFP+ vs QSFP28: How to Choose the Right Optical Transceiver SFP vs SFP+ vs QSFP28: How to Choose the Right Optical Transceiver

Nov 3, 2026

Walk into any spare-parts warehouse for carrier networks and you will see shelves of small metal modules that all look the same. They are not. Picking the wrong transceiver means a link that never comes up — or worse, a link that comes up and flaps under load.

SFP: the 1G workhorse

SFP (Small Form-factor Pluggable) carries up to 1 Gbps. You still find it in access switches, OLT uplinks and older SDH/PTN equipment. Common variants: SX (850 nm, multimode, up to 550 m), LX (1310 nm, single-mode, 10 km), and EX/ZX for 40–80 km reaches. SFP slots accept only SFP modules — you cannot get 10G out of an SFP cage.

SFP+: 10G in the same footprint

SFP+ keeps the SFP dimensions but raises the lane rate to 10 Gbps. Most SFP+ ports are backward-compatible with 1G SFP modules, which makes migrations painless: reuse the chassis, swap the optics. Typical parts are SR (850 nm, 300 m over OM3), LR (1310 nm, 10 km) and ER (1550 nm, 40 km). A typical example is the OSX010000 SFP+ 10G single-mode 1310 nm 10 km module, widely used in Huawei access and aggregation gear; for short-reach multimode, the Aruba J9150D 10G SFP+ SR (300 m over MMF) is a campus staple.

QSFP28: four lanes, 100G

QSFP28 aggregates four 25G lanes for 100 Gbps. It is the default for spine-leaf data-center fabrics and 5G backhaul. Variants include SR4 (100 m over OM4), CWDM4/LR4 (2–10 km single-mode) and PSM4. Note the caveats: QSFP28 needs four fiber pairs for SR4 (MPO connector), and breakout to 4×25G SFP28 requires switch support.

How to choose

Three questions decide it. First, port speed: match the module to the cage — SFP for 1G, SFP+ for 10G, QSFP28 for 100G. Second, reach and fiber type: multimode for in-room runs, single-mode beyond 300 m. Third, compatibility: coded optics matter — a generic module without the right vendor EEPROM will be rejected by many switches. When in doubt, match the exact part number of the failed unit.

Need a quote on any of these? We stock legacy and current optics in Yantai and Hong Kong warehouses — send your part list and we reply within 24 hours.

Walk into any spare-parts warehouse for carrier networks and you will see shelves of small metal modules that all look the same. They are not. Picking the wrong transceiver means a link that never comes up — or worse, a link that comes up and flaps under load.

SFP: the 1G workhorse

SFP (Small Form-factor Pluggable) carries up to 1 Gbps. You still find it in access switches, OLT uplinks and older SDH/PTN equipment. Common variants: SX (850 nm, multimode, up to 550 m), LX (1310 nm, single-mode, 10 km), and EX/ZX for 40–80 km reaches. SFP slots accept only SFP modules — you cannot get 10G out of an SFP cage.

SFP+: 10G in the same footprint

SFP+ keeps the SFP dimensions but raises the lane rate to 10 Gbps. Most SFP+ ports are backward-compatible with 1G SFP modules, which makes migrations painless: reuse the chassis, swap the optics. Typical parts are SR (850 nm, 300 m over OM3), LR (1310 nm, 10 km) and ER (1550 nm, 40 km). A typical example is the OSX010000 SFP+ 10G single-mode 1310 nm 10 km module, widely used in Huawei access and aggregation gear; for short-reach multimode, the Aruba J9150D 10G SFP+ SR (300 m over MMF) is a campus staple.

QSFP28: four lanes, 100G

QSFP28 aggregates four 25G lanes for 100 Gbps. It is the default for spine-leaf data-center fabrics and 5G backhaul. Variants include SR4 (100 m over OM4), CWDM4/LR4 (2–10 km single-mode) and PSM4. Note the caveats: QSFP28 needs four fiber pairs for SR4 (MPO connector), and breakout to 4×25G SFP28 requires switch support.

How to choose

Three questions decide it. First, port speed: match the module to the cage — SFP for 1G, SFP+ for 10G, QSFP28 for 100G. Second, reach and fiber type: multimode for in-room runs, single-mode beyond 300 m. Third, compatibility: coded optics matter — a generic module without the right vendor EEPROM will be rejected by many switches. When in doubt, match the exact part number of the failed unit.

Need a quote on any of these? We stock legacy and current optics in Yantai and Hong Kong warehouses — send your part list and we reply within 24 hours.

Back to newsبازگشت به اخبار

Post commentارسال دیدگاه

Comments are reviewed before publication.دیدگاه‌ها پس از بررسی منتشر می‌شوند.